Metal detecting general tips

The only thing for sure that can tell trash from treasure is a shovel. .

Tired of loose detector knobs? A 17c Tip I went to a hardware store today & for 17c each got an o-ring for the Tesoro Eldorado GB Knob & the Fisher 1266-X Sens Knob. It took about 30 seconds to slip the o-rings over the knob & into place, They worked great the knobs now stay in position. Take your detector with you to make sure you get the correct o-ring size. Posted on Coinist's MD Forum April 24, 2000

Pinpointing - A simple way to detune any detector with a pinpointing feature is when the coil is over the approximate center of the target quickly release and squeeze the trigger. This will shrink the target size making the target easier to locate. You can repeat this detuning as many times as necessary. If you completely lose the signal move your coil off to the side of the target, release & squeeze the trigger, and then repeat the above procedure.

Hi Rick, the real trick to using discrimination is to be able use the correct amount of discrimination based upon the site you are hunting. When you are in an older place I would use the minimum disc necessary to do a realistic job of hunting. In newer trashy areas I would tend to use more disc and dig less trash while going for more coins. I don't think anyone should use a preconceived disc setting as one should be flexible and set it according to the site one is hunting. Posted on the Old Tesoro Forum May 18, 1998
Ground Balancing - The way to check your detectors ground balance or automatic ground balance adjustment is to hold the detector about two feet in the air (while in All Metal Mode) and quickly lower the coil to about one inch above the ground. If you hear a slight increase in the threshold that means the detector is balanced slightly positive. Which is the setting preferred by most detectorists. If the threshold increases a lot or the detector gives of a loud beep the detector is set too positive. If the threshold decreases and then gets loud when you raise the coil the detector is set too negative. If changing an IDX's ground balance adjustment keep in mind that it could throw off the ID accuracy. If you do not feel confident making an adjustment to your detector let it alone or take it to someone who is experienced at making these adjustments.

Inexpensive Headphones - If you are looking for a good pair of headphones I would go with the Optimus Pro 35 or the Optimus Pro 40 set made by Koss at Radio Shack. On sale the Pro 35' s (which are a small light weight set) can be purchased for around $20 & the Pro 40's (which are a full size set) can be purchased for less than $50. The Pro 40's (Official Rock & Roll Headphones) don't have a volume control but you can get an adaptor with a volume control for about $3.95. Or if your detector has a volume control you may not need one. The other inexpensive set I would recommend is the Calrads for about $20. For the price they can't be beat as I keep a set in my trunk as a backup.

Hunting Football Fields As always if there is a concession stand or ticket booth. Basically where ever money is exchanged I would search around. As far as the field itself I have done the best from the 10 yard lines into the end zones as most kids that play on the football fields will only play on one side of the field. The players in football games will usually not lose much as they are wearing uniforms (not carrying money). But anyway most of what is lost on the football fields come from the cheer leaders along the sidelines (Jewelry) or kids playing pick up games around the end zones (especially under the goal posts). Check good around the end zone lines as kids will dive into the end zones while copying their favorite players. These are the areas I would search first. If you have time I would windmill around the whole field. If there are grassy areas where people sit around the field or if they park their cars in grassy areas around the field these are good spots also. I have found many rings and some silver coins on football fields so take your time and have fun. PS keep your eyes open while you are hunting as I eyeballed an expensive gold & silver religious cross laying on the ground in the end zone with a value of $200 to $400.
Digging more signals For those that are using a Target ID when digging a variety of signals you will have a better chance at Jewelry, Tokens, & say an Old Silver Quarter & Nickel in the same hole which depending on the placement of the coins may read like a tab or a zinc for example. As always there are trade offs. By digging more you will probably come home with less coins as you will be digging more non coin signals but your chance for a truly great find will be increased by finding a target such as: Gold, Tokens, Flying Eagles, IH's, 3 Cent Pieces, Rings & Jewelry, & finding more than one type of coin in the same hole or a good target in the same hole with a piece of junk. Also don't forget to rescan the hole after you remove an unwanted pull tab or piece of junk as you may have removed the mask that was covering a nice coin.
Too Much Emphasis on The Detector and Not the Detectorist? With all the discussions about which brand & model detector is the best. I think the one thing that is often left out of the discussion is the person doing the detecting. I think the finds of Karl Von Mueller, H Glenn Carson, & Charles Garrett would top most of ours. Even with us using the new top of the line brands & models. If a good target is around any detectorist worth his salt is going to find it with any of the top brands. To sum it up: They'd take their detector and beat yours and then take your detector and beat theirs. Posted on the Old Tesoro Forum January 21, 1998

How to Find the Old Ones Pick out an old site and go slow. Most of the old ones will be deeper which means the detector signal (which is like this V) will just about have to be right over the center of the target to detect it. Then if you add in the presence of junk or a coin on end you get the idea. Slow down, dig the weak & iffy signals, and you will start to find more of the the old ones. Posted on Coinist's MD Forum August 18, 2001

Whats the safest way to trade detectors without getting burnt. I would be grateful for any tips. JC First find out who you are trading with. Also you could involve a third party that each of you trust. Each of you send your detector to him and then if he gets what each of you said he should in the way of detectors he sends them to both of you. If he doesn't think one or both of the detectors is what it is supposed to be he contacts both of you and finds out how you want to proceed. There is no 100% sure way. Even on a COD transaction someone can send you a box of garbage as most postmen will not let you inspect the contents of the box as they consider it a done deal when they deliver the package. Posted on Coinist's MD Forum January 17, 2002

Urban Coinshooting for Older Coins

You live in a city or urban area and you have to work for a living which means your hunting and traveling time is limited but you would still like to find some old coins to go along with the clad coins that you find at the modern parks and schools. Today is special in that you don't want to settle for some clad coins you would like to find an old coin to post about finding on your favorite forums and show to your friends. It's summer and although researching is important today you just feeling like hunting. The wife and kids have gone to her parents house for the day and now it's time to hunt.

You are having your morning coffee and thinking where to go to find some older coins. Obviously you need and older site. The older sites you are aware of come to mind. Should I give the old 1800's park another try even though it has been pounded hard and hunted for years? Let's see are there any spots there that could have been missed by others? There is the slope area surrounding the old pond and skating rink that may make a good area to hunt as others may have overlooked it or only hunted it for a short time simply because it was too hard of work detecting on the side of a hill. Then there are the areas around the base of the trees or the flower beds that are just dirt now as the flowers may not have been planted yet. Then there is the area where they removed the old fence and are going to put up a new fence around the old house in the park. That would open up a strip of ground a couple feet wide around the house which might contain an old coin or two. Are there any entrance and exit routes leading to and from the park that may not have been searched much if at all? How about the area right next to the sidewalk that runs thru the park?

Then there is the old school. While myself and others have hunted the main school yard many times what about the not so obvious areas or the surrounding areas?. For instance the area between the street and curb that surrounds the school. Or what about the front of the school as it may not have been hunted as much since the hunter would be more visible to the public and some tend to shy away from that. Also there are those big bushes in front of the old school that may not have always been there. Could they be hiding and old coin or two? What about the corners across the street from the school where students waited for the school bus while engaging in some good natured horse play that may have resulted in an old coin being lost?

While to the more experienced Coinshooter this type of thinking may be basic and second nature but by using these simple tips I have found many old coins using the above methods in old parks and schools. Obvious places that many others had given up on as hunted out years ago. Does this type of hunting work every time? "No" But in the long run this type of thinking will help you find older coins that you thought only others found.

When you go coinshooting at an old site hunt the not so obvious areas and the areas you feel have been hunted the least. While you may not have the quantity of finds in the not so obvious areas you will have better quality targets in those areas. If any of you try some of these methods out I would enjoy hearing how you did. Posted on Coinist's MD Forum May 2, 2000

Locations for Metal Detecting Finds

Old and rare toys and games are a particular collector¡¯s favorite, as are newer ones that are connected with popular films and TV series. The latter need to be in really good condition. 20 years ago, as a kid in his mid- teens, my cousin was buying Star Wars figures and keeping them sealed in their packets. They are now worth up to 250 dollars each!

While taking a creative writing course in college, my instructor introduced me to an invaluable tool--a Writer's Treasure Chest. This tool is easy and fun to make and will come in handy time and again throughout your writing life.

When you think of treasure hunting, maybe gold coins and precious stones come to mind, but it doesn't end there. You can start in your own attic to see what treasures you find. Then you can check out some of the more unusual ways to go treasure hunting. However I also have friends or have found items running into hundreds of thousands of pounds. I suppose at the end of the day there is an element of luck. I'm sure that those who Pan Gold and do Wreck Hunting or Bottle Digging will say exactly the same.

When you are very clear about what you want, you attract the energy and open yourself to opportunities you wouldn¡¯t have been receptive to before.

Promising Locations for Metal Detecting Finds

If you're at a loss on where to start searching for buried treasures, get your metal detectors and flashlights ready and blinking because we have several suggestions in mind for you:

National Forests - It's a good place to start exploring because most rangers are courteous and quite willing to help metal detecting aficionados like you. You're also allowed to own any finds you detect as long as it's less than 50 years old, file a claim, and even prospect for gold.

Indian Reservation - These are very promising locations, indeed, but you have to be Cheyenne to legally search in Cheyenne land and so forth. If you don't look Indian, you'd better find someone who is.

Backyards - Yes, just your very own backyard could easily do, especially if it's OLD land. You can also ask your neighbors' and friends' permissions if they're willing to let you delve into their backyards. Promise them a share of your finds if that will help. Lastly, it's always best to procure written consent to avoid future complications.

Beaches - With the sun, the breeze, and the waves doing their things, it's no wonder that beach lovers are so caught up with nature's beauty that they tend to misplace and lose some of their valuables.

Photo Challenge Treasure Hunt in Sussex is a wonderful team building exercise that offers ultimate scope to explore and rediscover famous places of Sussex and its surroundings.

Down in that treasure chest also lurks some of your lost potential from childhood, the things you could have done; the ways you could have developed if only things had been different.

There are portable walk-through metal detectors that can be easily installed and stored away. They are compact and lightweight and usually require no initial calibration. Prices of walk-through metal detectors range from $3000 to $6000 depending upon the brand and features provided. The general idea is to play treasure hunt on whatever scale you feel the recipient can manage...E.g. Young children from 4 to 10 would probably be restricted to the house and garden. Teenagers may like to travel to local malls or shops..for adults unless you have a rocket to play with ..the world is big enough!!

Hidden in a warehouse in the small town where I used to live, was a mountain of old boxes. It was the leftover inventory of a wooden clock factory that had gone out of business. The owner of the clocks had let them sit there for at least ten years. Finally someone explained to him how he could sell them on Ebay, and he realized the treasure he was sitting on.

Playgrounds - Be sure to search specifically on grassy or shady areas as these are the places that people mostly frequent, and consequently, lose things. Finding a toy isn't that bad if it happens to be a charming limited edition, eh?

Fields - It's best to head out for the fields after a heavy downpour because you're more likely to discover hidden riches at these times. Don't forget to wear proper rain gear or you'll be too sick afterwards to enjoy your finds!

Riverbanks - Drop by at your local library and research for riverbanks that were once the site for ferry launchings or important social events. These particular spots are more likely to yield delightful finds than other places.

Cemeteries - Most cemeteries are built on very old lands. If your metal detector happens to indicate prospective finds under the grave, however, do respect the dead, and move on to another path.

A Word of Warning

Wherever you choose to rummage around for long-forgotten and long- lost booty, make sure that you have legal permission to do so at that place. Ask around if authorization, a license, or any legal document is required before you can hunt to all your heart's content.

Derbyshire, with its scenic beauty and perfect backdrop for exciting outdoor activities looks like the best place for planning your corporate events.

However, there is a simple tool that anyone can make that will make war recovery easier. simply taken old 5 gal. drywall bucket and cut out the bottom. also remove the handle as it is metal and may interfere.

When looking for a find, what should you look for? If you can already imagine the object taking on a new life as something else, thats great.

Recognizing that your own treasure chest of positive memories and capacities are more precious to you than any winnings is what THE ENCHANTED SELF is all about. When we begin to acknowledge that we ourselves are our own messengers of enchantment, then we can begin to brighten our lives and the lives around us. Find out more about metal detectors at metal detector info site.

Metal detecting is an exciting, adventurous, and fun way of finding valuables or items of sentimental value to us. Using the metal detector in places such as parks, beaches, woods, playgrounds, fields, riverbanks, old cellars and graveyards, even on our own backyards is a good way of bonding with families, friends, and colleagues. It is a fascinating hobby, too.

About the Author What to look out for in Metal Detectors? Find out at http://www.detect-metal.info

Tips for Researching for New Metal Detecting Spots

A third style, the Printed Spiral, is made only by Tesoro for use with pulse induction circuitry. It offers good sensitivity to a broader range of target sizes and improved sensitivity to less conductive targets such as fine gold chains. All searchcoils are electrostatically shielded and waterproof. Be it out of sheer hobby or more on the professional level, you really would not perform well treasure hunting if you do not have a good metal detector to explore with.

Hand-held Metal Detectors are designed to safeguard security-sensitive areas like schools, courtrooms, corrections facilities, sports events, businesses, nightclubs, bars and other public areas and events. They are used along with walk-through metal detectors. Metal detectors are electronic devices that are used to find traces of metal usually from the ground, a person, or cargo. This metal could be anything from discarded pieces of aluminum to buried treasures. These devices can penetrate sand, soil, wood and other non-metallic substances.

Tips for Researching for New Metal Detecting Spots

Metal detecting is not a particularly popular hobby, but the good thing about it is that more and more people are getting hooked on it. Metal detecting is an activity that can be very thrilling and educational at the same time. Metal detecting is really a form of treasure hunting. Most of the valuable items in the pre-modern and modern world are made with or are embellished with different kinds of metals. Metals have been the founding material that treasures are built from and this is the reason people are detecting metal.

A crucial factor to consider when going on a metal detecting journey is the location. There have been many metal detecting enthusiasts before and the more popular sites have already been cleaned up. How does one find his own treasure land? What are some ways of finding fresh metal detecting spots when everyone else has depleted the easy ones? Here are some great tips.

1. Go on-line

The world has been transformed by the technology that is the Internet. Information has been pooled into one massive portal where people can interact and exchange valuable stories. There are many websites out there that give a sneak peek or educated guesses as to which spots would most probably be great for metal detecting.

As stated earlier, metal detectors could really be expensive. You can cut on cost if you cut on features. Try to look for the best bargain by enumerating the features you are going to need against the one that you can leave off. Any place there is construction and the ground is being cleared, that is a great place to start treasure hunting. Successfull treasure hunting starts with having the right metal detector. But which type of metal detector should you get? Complete info on metal detectors and treasure hunting at detect-metal.info.

My recommendation is to simply allow mining companies to clean up this contamination in the California watershed through large dredging and sluicing operations without risk of civil or criminal liability, and possibly for a profit. We must also allow recreational miners greater access with fewer restrictions in the smaller creeks and streams that would be inaccessible to mining companies.

The good news is that prices have never been lower for such easy to use full featured automatic detectors. A good way to view the purchase is to decide how much money you are comfortable spending. The large coil can be found in the search coil of the detector while the small coil is found on the System Control Pack. The coils are connected to an oscillator which produces pulses of current. The pulse passes through the coils in order to generate radio waves.

Metal detectors work on the principal of electromagnetics and their effects on conductive metals. There are actually two separate elements in the coil of a typical unit. One is a high-powered coil of metal which uses the battery power to generate a penetrating magnetic field.

2. Get a history book

Knowing the details of your local town is a good way of spotting new areas for metal detecting exploration. Try to spot the not-so-popular historical events in your area and try to detect there. One should always believe that there are still places that are left out by the previous enthusiasts of metal detection.

3. Go on trips

When taking a vacation somewhere, take your metal detector if it would be possible. Just try your luck on the beach or in the woods, you never know what you will find. Besides, it's a great way to pass the time if there are no pending activities.

4. Try topography maps

Topography maps and GPS gadgets are really great tools for finding and locating new spots. If you feel that you have found a place that is really worth going to, look at the topography map to find the easiest way of getting to the place and take along a GPS if possible. There are a lot of treasure to find out there, all one has to do is be patient and enjoy what he is doing. Keep on detecting!

Come find out more on metal detector reviews in order to pick the perfect one today! A recent study proves that hand-held metal detectors are just as accurate as x-rays in finding coins and other metallic objects swallowed by children. So next time you loose that ring at the beach or you dime at the park remember there are ways to find you beloved object. Have Fun.

Using the product is the best way to learn its features. And later on you can easily read the signals. Another plus point is that it is very easy and convenient to carry.

When hand-held detectors are switched on, a red signal pattern in transmitted from the coil to the ground. When the signal comes in contact with a metal, it interrupts the signal and the detector alerts the user with an audio signal and flashing lights.

The Secret to Beach Metal Detecting

Are you purchasing a detector to use occasionally at a lake or beach? Or do you now find yourself with more available time and can look forward spending considerable time with your new hobby? It is a fact that most of the detectors now in the marketplace are pretty good. There are certain features needed for certain places the device is going to be used for. If you intend to use it on the beach, the terrain wont be that rigorous. But you are going to need waterproof protection.

If this is your first metal detector purchase, consider getting some professional and expert advice to make sure that you have making the right choice. Metal detectors usually come with a complete control box containing the controls, circuitry, batteries, microprocessor, and the speaker. Metal detectors also include a search shaft that connects it to the coil and the control box. Metal detectors are electronic devices that are used to find traces of metal usually from the ground, a person, or cargo. This metal could be anything from discarded pieces of aluminum to buried treasures. These devices can penetrate sand, soil, wood and other non-metallic substances.

The Secret to Beach Metal Detecting

Metal detecting can be a great hobby, but it can also be one remarkable source of income. The beach is one of the favorite spots for people who are into metal detecting. Not only are they able to obtain rare metals but they can also enjoy the lovely atmosphere in the beach.

With the soft, damp sand along the beach, finding different kinds of metals can be enjoyable. It is more like having fun than finding treasures even if there are not so many finds after a hard day's metal detecting activity. Just getting the sand beneath your feet, rumbling waves along the seashore, and the beautiful scenery in the area is worth more than what treasures of gold and silver can bring. However, if you really want to get a good start in beach metal detecting, it is best to keep these things in mind and head off to the beach with a plan for a remarkable kickoff.

1. Saturate the area

With the growing popularity of beach metal detecting, many people are enticed to try the activity. It is not surprising to find many people crowded into a certain beach or area. In this kind of situation, competition in beach metal detecting becomes tight. This means that you probably will have a lower chance of finding treasures.

Youve got to buy a metal detector that could withstand normal wear and tear longer than its competitors. The longer the metal detector can serve you, the better your return on investment will be. ome detectors have more ways of adjusting the "fit" to the person. Some of the other ways that detectors adjust are that the arm cup can be raised or lowered, and the box containing the board and controls can be taken off of the pole and mounted in a small pouch. Many people say to us "I have always wanted to do this!"

Any place there is construction and the ground is being cleared, that is a great place to start treasure hunting. Successfull treasure hunting starts with having the right metal detector. But which type of metal detector should you get? Complete info on metal detectors and treasure hunting at detect-metal.info. he man of the house would have buried a cache of money someplace that could be seen from the bedroom window. Loose change could have been dropped when getting in or out of vehicles.

The large coil can be found in the search coil of the detector while the small coil is found on the System Control Pack. The coils are connected to an oscillator which produces pulses of current. The pulse passes through the coils in order to generate radio waves. Remember, the higher the coil is above the surface the more depth you will lose. If they've got a old coin that is 6 in. below the surface, and your detector can detect 8 in., and the coil is 3 in. above the ground, you will miss that target. If the coil had been directly upon the ground you would be able to detect that target.

Therefore, in order to get an edge over the others, why don't you saturate the area and/or find those beaches that have not yet been discovered. Any beach for metal detecting is always worth visiting.

2. Do not be so easy on your metal detectors

The prices of metal detectors cannot simply be underrated. Yes, metal detectors as well as their coils can be very expensive. No wonder many people are extremely careful with their coils and try not to scratch them by keeping them too far above the sandy beach. The results? Negative. What do you expect? You will definitely not find anything if you have your metal detectors too far above the sand. The point here is that if you want to find considerable results, you have to dig it.

3. Stay away from weekends

Beach metal detecting is extremely popular these days. That is why only a few people are only getting good results when they head off the beach. There are just too many people in the area. To avoid this problem, it is best to visit the beaches during the week. By doing this, you can expect fewer people in the locality. Indeed, beach metal detecting can be great fun, especially if you know where to find your treasures! Find out more about metal detectors at metal detector info site.

A recent study proves that hand-held metal detectors are just as accurate as x-rays in finding coins and other metallic objects swallowed by children.

Now that you have learned the three different types of metal detector, it¡¯s up to you to make your choice as to what type of detector you wish to use for your searches. Remember, the higher the coil is above the surface the more depth you will lose. If they've got a old coin that is 6 in. below the surface, and your detector can detect 8 in., and the coil is 3 in. above the ground, you will miss that target. If the coil had been directly upon the ground you would be able to detect that target.

About the Author: www.detect-metal.info

Picking The Right Metal Detector for You

So you are looking to purchase a metal detector but first you should check what features each one has prior to making any purchase. Remember that although metal detecting can be a fun hobby if you do not have the right equipment you can be wasting both time and money.

The first thing to consider when buying a metal detector is the price. Certainly the more expensive metal detectors will have more features, but if you do not want to break the bank then it well worth considering purchasing a cheaper model. The prices of metal detectors range from $50 up to $400 and it all depends on what features you want.

There are some metal detectors which use Beat Frequency Oscillation (BFO) which contains two coils of wire (one large and one small). The larger one can be found in the search coil of the detector while the smaller one is found in the system control pack. These coils are connected to the oscillator which produces a pulse of current and this passes through the coils to generate radio waves. There is a receiver within the system control pack that receives the radio waves and produces a series of tones (beeps) based upon the frequencies coming from the radio waves. As soon as the detector search coil encounters a metal object (say a coin) it surrounds it with a magnetic field which caused interference to the frequency and thus the tone produced by the detector will alter.

Certainly when looking at purchasing a metal detector the best ones to choose are those that are fitted with BFO technology as it is both the easiest kind to use and are also cheaply available to own.

Another kind of metal detector is those that use PI (Pulse Induction). This uses a single coil or even a series of coils which work as a receiver and transmitter. Short bursts of electricity pass through the coil or wire causing magnetism and the magnetic fields will reverse their polarity if the bursts of electricity are cut off or stopped. Then more pulses are created when a sharp electrical spike is produced and this whole process is repeated and will give off different kinds of echoes depending on what kind of metal is detected. Unfortunately this kind of metal detector is not suited for discriminating between different kinds of metal or coins as is better suited to being used in areas where salt water and metals are detectable.

Finally we come on to the metal detectors known as VLF (very low frequency) models which have two search coils. The first coil is the "transmitter coil" and this quickly transmits electricity to the other coil known as the "receiver coil". This one receives the frequencies that are bounced back any objects that the coil detects and this type of metal detector is best for use when just looking for different types of metal and not one in particular such as gold.

Well now that we have provided you with information in regards to the different types of metal detectors that are available it is up to you which one you decide to purchase in order to carry out your searches.

metal-detector-guides.com

Find Lost Treasure By Metal Detecting in the Woods

If you are avid metal detecting fan you are always looking for new places to discover treasure. You may like to go to the beach, to the park, or different playgrounds in your area. These obviously are wide open spaces and give you a lot of area you can cover with the metal detector. But you know what; metal detecting in the woods can be just as much fun and just as profitable.

If you decide to metal detecting in the woods here are some things you may consider and the places that you may look. You can look on old trails, trail made in the past that had now overgrown, trails used for wagons in the past, and anywhere there are signs that houses may have been in the area.

Back before automobiles and streets were readily accessible people had to make their own trails so along the way they would stop. Just like coins that you find in your seat cushions or in your car that have fallen out of your pocket the same thing could have happened to people who used these trails. Also, maybe during these travels they decided that some of the stuff they were carrying was too heavy and put it aside.

Many times houses that used to sit in the woods are no longer there and have not been there for quite awhile. People used to live in these houses so obviously they have possessions and any time you have a house there will be old remnants left behind. Over time they just get covered up and wait for you to come get them.

A good way to make metal detecting in the woods profitable is to go to a library in your area and see if there were any maps from a while back. If you do find maps this will give you a good idea of where some trails and where houses were located there are no longer there. Once you find where the houses and trails were located, bingo, you may just found the jackpot.

If you're looking for a new place to metal detect and a new adventure try the woods in your area, just think about people who have lived there in the past and some of the stuff they may have left behind. Finding treasure in the woods may be easier than you think.

J C Christian is an avid follower of metal detectors and how metal detectors work. He runs an informational site that follows Garret Metal Detectors, Fisher Metal Detectors, Tesoro Metal Detectors, and Kellyco Metal Detectors just to name a few. Go to http://www.metal-detector-guides.com to find information to help with everything metal detecting.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

Metal detecting evolution

It really is hard to believe that metal detectors have been around for much longer than many people know. It was towards the end of the 19th Century that many scientists and engineers began to use their growing knowledge of electrical theory in order to develop a machine which would pinpoint the exact location of metal. Certainly the use of such an instrument would provide a huge advantage to any miner who was looking for ore bearing rocks. Then a German physicist by the name of Heinrich Wilhelm Dove invented the induction balance system which was incorporated in to the production of metal detectors 100 years later.

Many of the early metal detectors were crude and used a lot of battery power and they often only worked to a very limited degree. In fact Alexander Graham Bell used one in 1881 to try and locate the position of a bullet which was lodged in the back of the then American President James Garfield after his assassination.

However, the real development of the modern metal detector began in the 1930's when Dr Gerhard Fischer produced a system for radio direction finding and was used to accurately navigate pilots around the world. Although this system worked extremely well there were some anomalies noticed by Dr Fischer when over terrain that carried ore bearing rocks or metal was placed close to the system. He therefore reasoned that it should be possible to design a machine which would detect metal using a search coil resonating at a particular radio frequency. So in 1937 he applied for and was granted the first patent for a metal detector. He soon found that his designs were being put to a more practical use as they were used to help detect mines during the Second World War. Although they were heavy, consisting of a vacuum tube and required separate battery packs they worked and after the war many of the surplus mine detectors that were on the market were being purchased by relic hunters who not only used them for fun but for profit as well and so the hobby of metal detecting was born.

Soon more and more manufacturers were producing their own versions of the metal detector from the Oremaster Geiger Counter produced by Whites Electronics of California in the 1950's through to Charles Garrett who invented and produced the BFO (Beat Frequency Oscillator) metal detector (and Garrett's is still one of the world's leading designers of metal detectors today).

But it was during the 1950's and 1960's because of the invention and development of transistors that many metal detector designers and manufacturers were able to make smaller lighter machines with improved circuitry and were able to run on much smaller battery packs. They were even reduced to a size that a child would able to handle easily and many did. In fact there was such a huge requirement for these early models that Companies sprang up not just in the USA but in Britain as well hoping to supply the growing demand.

Even today the trend for metal detecting as a hobby still continues and the companies such as Garrett Metal Detectors and Fischer Metal Detectors are still producing new designs and models all the time.

J C Christian is an avid follower of metal detectors and how metal detectors work. He runs an informational site that follows Garret Metal Detectors, Fisher Metal DetectorsFisher Metal Detectors, Tesoro Metal Detectors, and Kellyco Metal Detectors just to name a few. Go to http://www.metal-detector-guides.com/ to find information to help with everything metal detecting.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

Gold Metal Detectors

Gold metal detectors are used to find small and large gold nuggets. Small and slightly small gold nuggets can be detected at medium depths. Large gold nuggets are the most difficult to search and locate. Gold metal detectors have ground balance modes for alkali soils and black sands for smooth operation. The maximum sensitivity of a gold detector helps to locate small gold bits at greater depths. It can operate with ideal frequencies for locating gold nuggets. The search coil used in gold metal detectors is water proof. Additional features of gold metal detectors are meter display, manual group balancing adjustment and discrimination adjustment. These supplementary features vary with the technology used in each type.

Gold metal detectors are generally based on digital technology. They have automatic and manual modes. The auto-trac feature cancels the ground minerals in seconds and then tracks to the changing conditions. The features include iron audio signal, LCD display and bar graph. A microprocessor monitors and stores the ground mineralization value. The graph displays the percentage of probability of iron and the amount of magnetic minerals in the ground.

Advanced gold detectors have maximum depth and super sensitive features. They have digital ground balance with switchable speed recovery. The ultra high frequency gold metal detector is designed to find gold nuggets at greater depths. They use elliptical search coils. The features include high sensitivity, high operating frequency, iron discrimination and audio boost facility. The mineralization settings may be low, normal or high. They can operate in mineralized soil with a three position mineralization switch. Some of the advanced gold metal detectors have three modes for speed tracking. Slow, medium and fast tracking modes help to improve the detecting. Advanced gold detectors can also resist dust and moisture.

Some of the advanced gold metal detectors have manual tune control feature. The manual tuner helps to select various frequency bands. Multiple frequencies help to attain more depth, sensitivity and more accurate targets. The tune control minimizes electrical interference from power lines, radar and radio transmitters. Gold metal detectors are lightweight, water proof, cancel noise and have ground balance and on board computer chip.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

Twelve Ways To Make Extra Money With A Metal Detector

If you’re the kind of person who is willing to put the time and effort into finding some of that lost money, you can make extra money, fast, while having fun.

I’m not talking about getting rich here. Although I know of people who have, however, I am talking about literally picking up lost coins that have been dropped over the years.

Do you want extra money without having to work at a job you don’t like?

Do you need some extra cash to go to dinner, or to pay a bill?

Are you a coin collector who wants to add to your collection?

Or perhaps you just like the idea of finding lost coins.

If you answered yes to one or more of the above, then try metal detecting.

Not only can you make extra money using a metal detector, but you’ll also enjoy the benefits of exercise in the outdoors.

There’s no need to spend thousands of dollars on an expensive metal detector with all of the bells and whistles either. You can purchase one for around two hundred dollars. Any of the major detector manufacturers have beginner’s models for this price. And if you stay with the hobby, and don’t become discouraged, you can end up paying for that detector with your found coins.

I know retired individuals who earn extra money by using a metal detector.

Young children are fascinated with metal detectors and have fun finding coins. It’s a great hobby to start them in.

Many people who purchase their first metal detector end up with a lifelong love of the hobby and become treasure hunters searching for buried caches and lost treasures.

Ten Places To Use A Detector To Make Extra Money

Once you purchase your detector read the owners manual and learn how to use it correctly. When you’re ready to go detect’en, here’s some great places to begin. I can’t guarantee how many coins you’ll find, but over time, with practise your finds will increase.

· Parks-
· Schoolyards
· Parking Meters
· Bus Stops
· Between The Curb and Side walk
· Fairgrounds
· Beaches
· Lost and Found
· Home Sites
· Old and new Church yards
· RV Parks
· Ball Fields

Parks and Schoolyards

Parks of all types yield a constant flow of lost and dropped coins. As an added bonus, lost jewelry like gold and silver rings are also being located.

How many of us lost our lunch money while playing in the schoolyard? It still happens today.

Parking Meters

I’m not talking about stealing them. Seriously though, I know one fellow who metal detects the grassy areas around parking meters. This is an overlooked area when it comes to metal detecting. People are dropping coins not only into the meters, but onto the ground as well.

Bus Stops

Same idea as those parking meters. Many people lose change as they fumble in their pockets or purses looking for bus fare.

Between The Curb And The Sidewalk

Here’s another area that is overlooked when it comes to metal detecting. That grassy area between a sidewalk and the curbing holds many coins. And like parking meters and bus stops they are in every city, town and village.

Fairgrounds

How about detecting the area of the nearest fairground? And if you can locate an old fairground, you’ll have those old coins to pick up as well.

Beaches

Any beach that has heavy use is a potential for finding lots of coins as well as silver and gold rings.

When people are at the beach and they are using sun tan lotions, the lotions make it easy for rings to slide off. If you can detect the water as well as the beach your in for some great finds.

Lost and Found

How about running an ad in your local newspaper in the “Lost and Found” section. People who have lost rings or jewelry will often pay a “finders” fee to anyone who can locate the item.

Home Sites

If you get permission to metal detect the yards of homes, especially the older homes, you’ll end up finding more than just lost or dropped coins. Artifacts of every kind can be found there. And with the popularity of ebay, anything can be sold. Just be sure to have the property owner’s permission to sell anything you find. Better yet, offer to split the selling price with them.

Old and New Church Yards

Wherever people gather they lose items. And church functions that are held outdoors are no different. If you can get permission to search the older churchyards where many picnics were once held, you’ll have loads of fun finding older coins and jewelry. RV Parks

I know a few individuals who own RV’s and they never fail to bring along a metal detector to detect the RV parks they stay at. With gas prices as high as they are today, finding coins in RV parks help to pay for that gas.

Ball Fields

Just imagine how many coins are lost while someone is sliding into home plate, or any base for that matter.

How about lost coins while playing tackle football, or running around on a soccer field. Men and women do lose coins and jewelry while participating in sports.

You can make extra money with a metal detector in many different areas. You will be limited only by your imagination. Research other areas that may interest you. Just be sure to ask for permission whenever you are in doubt of where you are going to metal detect.

Article Source: http://EzineArticles.com/?expert=Frank_Pandozzi

Underwater Metal Detectors

Underwater metal detectors are widely used by underwater search and recovery teams. Treasure hunters, archaeologists, sport divers, military and law enforcement people use underwater metal detectors for different purposes. Underwater construction companies use underwater metal detectors for pipeline or cable locating functions.

The common features of underwater metal detectors are depth, alerts, ground balance, detection mode and sensitivity. Some of the underwater metal detectors can adjust the search depth. Better quality detectors give distinctive alerts, depending on the type of metal sensed. Underwater metal detectors have different detection modes for searching and prospecting. Most underwater metal detectors can be used on both fresh and salt water.

Underwater metal detectors are based on digital technology. They have different operating modes. The normal mode works with a single tone. Normal mode is used for beachcombing and other prolonged searches. The standard discrimination mode is for conventional pulse detection. Slight audio signals indicate small or deep targets, while strong signals indicate large targets. A discreet discrimination mode provides more enhanced and precise targets discrimination. The metal detecting unit consists of pulse width control. This feature helps to adjust depth, sensitivity and battery life of detectors. Underwater metal detectors have deep searching circuitry. Other features include operating frequency, search coil and headphones.

Some underwater metal detectors use advanced pulse induction technology. This provides more detection depth and stability in mineralized environments. The audio threshold adjustment control shows individual detecting styles. Automatic ground feature allows the user to set ground track for optimum performance. Underwater metal detectors have different control housing configurations. The adjustable operating frequency helps to minimize the electrical interference.

Advanced underwater metal detectors have electronics built into the headphones. They reduce the weight of the detector. They consist of heavy duty negative buoyancy search coil, and have crystal controlled operating search frequency. Advanced underwater metal detectors consist of permanently encapsulated high output head phone transducers. The headphone ear cups have heavy duty polymer ear surround and noise blocking features. They can also operate in beach, rain or storm. Other features of advanced underwater metal detectors are silent search, hand grip, armrest and isolator.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

Metal Detecting on The Beach: find suitable metal detector

As you will often find metal detectors are used for treasure hunting and finding relics as well as there being many models and types available each will have its own set of different features, as well as the quality and reliability of each model differing also. Certainly each metal detector available has its own disadvantages and advantages.

But like many people you are unsure what kind of metal detector you should purchase and hopefully the information provided below will help you in your quest to find one that is suitable for use on a beach.

The first one we are going to look at is the White Spectrum XLT. Not only is it easy to use but it is well known for being user friendly (even a beginner should have no problems with this one). There is a manual available for this metal detector which is easy to understand. Often you will find that most people use this model when either in Beach or Jewelry mode at the beach (it also has a relic mode but this does not seem to work as well on the beach). This model has the added bonus of being very convenient to carry.

Now we are going to look at the White Pro XL 6000 which many people buy because of its look. This unlike the White Spectrum has less buttons for you to scroll through when you need to adjust or change settings. Yet it still may take you some time to familiarize yourself with all its features but once you do you will see how useful they can be. Unfortunately although the Pro XL 6000 seems to have more depth and intensity than the Spectrum, there is one fault with this model in relation to the knobs on it which can become loose and you have to be careful not to knock them when making any adjustments. Also any jarring or bumping to this model may also result in you having to start or reset any adjustments you have already made because of its knobs being so sensitive. In fact some people who use this model have found that rubber bands work quite effectively when wrapped around the knobs to stop them moving or becoming loose.

Ideally when purchasing any metal detector it is best to buy one that is light weight this is especially important when you are looking for things on either a riverbank or in a body of water. Although it is good to know how to make adjustments to the frequencies of the metal detector especially when using it on a beach it is also important to find the right place or location for using it. Preferably the modes on any metal detector should be adjusted so that the depth and intensity will be specified and clear when using in any location not just on the beach and always familiarize yourself with the metal detector you are using prior to commencing any searches so that you can get the best results possible.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

Cheap Metal Detectors

Metal detectors are used to find hidden metal objects in baggage, soil, or in a person?s body. Using electromagnetic induction principle metal detectors give alarm signals to identify hidden metal objects. Metal detectors are used for various purposes such as security maintenance, item recovery, archaeological exploration, and geological research. Cheap metal detectors are available in hand held, waterproof, and walk through models. The price depends on the brand, performance and features of the equipment.

Sentrie LC is a cheap walk through metal detector which can scan weapons and handguns of up to 3.5 ounces. Walk through metal detectors are reliable, fast and have high sensitivity to all metals. During sell outs, brands such as Tesoro, Whites, Prizm series, Fisher, Garret, Bounty Hunter, and Mine lab offer rock bottom prices for metal detectors. Discounts are also available during product promotional sales. Portable walk through metal detectors cost low and they are very efficient in detecting small objects. Even though the regular price of this model is around $4800, during sales the price is slashed to about $3900.

Hand held metal detectors are cheap, lightweight, sensitive, and radiation free. This model is easy to use, reliable, and requires less maintenance. Commercial, professional, all-purpose, beach, gold metal, relic metal and 2-box deep searchers are different types of hand held metal detectors. Garret Enforcer G-2 is one of the cheap metal detectors with high quality performance.

Cheap metal detectors are also available from shops which sell used metal detectors. Price of all purpose used metal detectors ranges from $275 to $700. Waterproof used metal detectors are cheap and cost around $500. As used metal detectors have no warranty, deal with a trusted dealer. Bounty Hunter metal detectors are comparably cheap waterproof models.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

A Look at Used Metal Detectors

There are many kinds of metal detectors - gold detectors, coin and jewel detectors, relic hunting detectors, beach-hunting detectors, and underwater metal detectors. Buying a metal detector can be a tricky affair. Before one decides to buy a metal detector, here are a few points to consider.

How often will it be put to use? If it is for a new hobby, it may be a good idea to buy a one with a lot of features.

Where it will be used? Will it be used on the beach, underwater, or in the woods?

Who will use it? If it for use in the family, there are detectors that have adjustable arm cups and separate pouches to mount the electronic box.

How much will you spend on a detector? It is advisable to be a little flexible in this regard so that one can buy one that most suits the requirements.

Buying used metal detectors usually offer the best value for your money. It is always best to buy used metal detectors from a respected dealer, rather than a classified ad. Most dealers offer a money back guarantee or a trade-in option. If you are buying from someone other than a dealer make sure it is someone you know and trust. Most dealers sell only tested metal detectors.

Prices of used metal detectors vary from $275 to $700 for all-purpose metal detectors. Underwater metal detectors can cost around $500. Most used accessories can cost $200. It is also a good idea to keep in mind that a used metal detector will not have the manufacturers warranty, but dealing with a reputable dealer will eliminate some of the risk.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

Industrial Metal Detectors

Industrial metal detectors offer maximum protection against ferrous, non-ferrous metal, and stainless steel metal contamination. Industrial metal detectors are used in a variety of applications. The typical areas covered are food, dairy, pharmaceutical, paper, rubber, medical, cosmetics, plastic, textile and chemical industries. Industrial metal detectors are highly successful in preventing downstream equipment from damage. These are also very useful for detecting weapons and bombs in packages or on people.

Different types of industrial metal detectors including underwater metal detector, airport metal detector, walk-through metal detector and handheld metal detector are available in the stores. Underwater metal detectors are widely used to locate metallic objects under water. A walk-through metal detector can detect concealed weapons at security checkpoints. It checks the whole body for metallic objects. Handheld metal detectors are an ideal solution for metallic screening applications. They are mainly designed and manufactured for security sensitive areas such as schools, airports, prisons, courtrooms and customs. They help to pinpoint miniature metal objects. An airport metal detector is also very useful for detecting weapons. Other types of industrial metal detectors are also available in most of the stores.

Industrial metal detectors function in different ways. Handheld metal detectors are light weight, radiation free and highly sensitive. Little maintenance is required in most of the cases. Besides metal detection, a walk-through metal detector includes operator interface and/or controls, electro magnetic compatibility, environmental tolerance, quality control and assurance.

Industrial metal detectors are designed and manufactured to meet the industrial requirements of individuals. Most of these help to reduce downtime and avoid catastrophes, thereby increasing productivity. In order to meet the growing competition in the field, some of the reputed manufacturers offer discounts, free shipping services and guarantee programs. Used industrial metal detectors are also found.

Some of the leading manufacturers in the industrial metal detecting industry are Compass Metal Detectors, DetectorPro, White's Electronics, Super Metal Detectors and CEIA USA Ltd.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

Metal Detector FAQs

A metal detector is an electronic device employed to detect traces of metal, generally from the ground, a person, or cargo. Metal detectors can effectively penetrate through soil, wood and other non-metallic materials.

How does it work?

Metal detectors use the principal of electromagnetism. Typically, a metal detector comprises an electronic box, transmitter, a receiver antenna and a battery case. By battery power, the transmitter generates a magnetic field. If a metal item passes through the metal detector, it becomes magnetized due to the effect of the magnetic field. On receiving the electromagnetic signature, the receiver sends a signal to the electronic box. There is a speaker to amplify this signal. This produces a beep sound, indicating that there is metal contamination.

What are the different types of metal detectors?

Depending on specific situations, different types of metal detectors are available. For example, there are metal detectors exclusively for prospecting gold. Likewise, special metal detectors are available for relic hunting. Underwater metal detectors, coin detectors, and walk through metal detectors are other prominent types. Multi-purpose metal detectors are also popular nowadays.

What is product effect?

When passing through the metal detector, some food stuffs tend to generate a signal although no metal is present in them. This is known as product effect. It is mainly due to factors including acidity, fat content, moisture content, salinity and temperature.

What are the factors that affect the sensitivity of metal detectors?

Product effect, size and type of metal contaminants, and metal detector opening size are some of the factors that affect metal detector sensitivity.

What is the warm up time for metal detectors after the power is on?

For accurate detection of metals, metal detectors must be allowed to warm up for at least 30 minutes after the power is on.

Can burned and rustic metals be detected using metal detectors?

Yes. But, the detection sensitivity is based on the shape and orientation of the contaminants. In addition, it is difficult to detect minute particles.

Can metal detectors detect non-metallic contaminants?

Metal detectors cannot detect non-metallic contaminants.

What are the accessories required in metal detecting?

Among the accessories required for metal detecting are gloves, probe, knife, gator digger, and ground cloth.

What are the precautions to be taken when cleaning metal detectors?

To clean the main unit of metal detectors, hot water less than 40 degrees centigrade can be used. The dirt and particles present in the detector head must be cleaned frequently. It is also necessary to clean its conveyor belts. Neutral detergent and a plastic brush with soft bristles can be applied for the purpose.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

Advanced Coin and Treasure Hunting Tips Finding New Locations to Treasure Hunt

There will always be new and profitable locations in which you can metal detect, you do not always have to go back to the same locations time and time again. If you use some imagination there are a lot of places that you can metal detect that you may have not thought of in the first place.

There are is lot of treasure, relic, and coins that have been just a lying around for centuries waiting for you to come find them. Think about what is going on in the area that you live in there possibly could have been civil wars, festivals, and anything you can possibly think of where large gathering of people come together. When people come together people tend to lose things and their loss is your gain.

If you live near a body water or the ocean you always go to the beach to find new treasure. There will always a lot of people who come to the beach and one thing is for certain people will lose valuables on the beach. The sand also makes it attractive because the digging takes less time than it would if you had to dig through dirt. You will always be able to find watches, rings, earrings, and coins on the beach because of the makeup of the sand people easily drop and lose valuables there.

After a concert or festival you will always be able to find things such as loose coins and jewelry. This is an area that a lot of people will be congregating all at one time, a festival or concert could be a target rich environment immediately after the event. Always make sure that you are allowed to metal detect at the location before actually starting out. Another good way to possibly make money is to give the location manager your card and let him know that you would be willing to give him your findings back to him if someone called in a lost and found request.

Any place you can possibly think of and a there will always be a chance if you can find something with your metal detector. Looking for more places for metal detecting will become more profitable and enjoyable. Take some of these tips and start using them today because there is treasure waiting on you.

J C Christian is an avid follower of metal detectors and how metal detectors work. He runs an informational site that follows Garret Metal Detectors, Fisher Metal Detectors, Tesoro Metal Detectors, and Kellyco Metal Detectors just to name a few. Go to http://www.metal-detector-guides.com/ to find information to help with everything metal detecting.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

Facts Revealed Behind Metal Detecting for Newbies!

So you finally decided to take the leap and buy metal detector, trust me you will not be disappointed in the excitement and the joy that it brings. Metal detecting is a hobby that many people take up and it really you get hooked. The sheer joy and excitement that metal detecting brings in finding a treasure is enough to make anybody addicted to metal detecting.

If you are new to metal detecting here are couple tips you should know before you get started out, these tips will make your metal detecting more profitable and more enjoyable. When you are new to metal detecting it sometimes can be difficult to find good information to help you get started, but in this article we will take a look at learning the local more about the metal detector, good places to metal detect, and planning your trip out before you start.

The first and foremost thing I would tell anybody to do before starting metal detecting is after you purchase a metal detector take it home and learn all of the controls and the maintenance for the metal detector. You will be so excited when you get the detector the first thing you want to do is take it out immediately and start looking for treasure, but to maximize your time is best to learn all of the options and everything the metal detector offers to you.

Finding places to metal detect is extremely easy and after getting a metal detector here are a couple of places you can start out with. Go into your backyard and just start metal detecting, this will give you a good feel for the equipment and you may find something in the process. If you live near any parks, this is a good place to go because typically a lot of people will go to the park. If you are close to an ocean beachcombing is really popular and can yield really good results.

If you are planning on taking a trip or spending a day metal detecting, always make sure that you plan the trip out to maximize your time and once you decide the location that you are going to metal detect on, contact the landowner and confirm that metal detecting is accepted. If you are prepared in the beginning you will be able to find more treasure.

When starting out in metal detecting the first inclination is to just grab the metal detector of the box and start running across the ground. After getting over the first wave of excitement you really need to start planning on how to use the metal detector, places to look, and maximizing your time. The information you just read it is a good starting point for you if you are just beginning in metal detecting.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

Buying a Used Metal Detector - 4 Tips to Make Sure You Do Not Waste Your Money

What options are available to you for buying a 2nd Hand or Used Metal Detector

You have now made the decision to buy a metal detector but are unsure whether you want to purchase a new or second hand model instead. However if your budget is a little tight then a used or 2nd hand model may be the best option for you. Below we provide you with some useful tips on when looking at purchasing a 2nd hand or used metal detector.

Firstly, we will look at what kind of metal detectors there are available. There are many types of metal detectors available and each is meant for a different purpose. However the ones that are most easily available are gold, coin and jewel, relic hunting, beach hunting and underwater metal detectors.

When considering purchasing a metal detector there are a number of factors that should be taken into account and it may be wise to consider the following points prior to any purchase.

1. How often will you use the detector? If it just to be used for a new hobby then it would be wise to choose one that offers you a number of different features and look at one that is not going to break the bank.

2. Look at where you are going to be using it the most. Will it be on the beach, underwater or in woods near to your home?

3. Who will be using it? Will it be for family use (some detectors come with adjustable arm cups and separate pouches to place the electronic box in) or will it be solely used by you.

4. What is your budget? It may be wise to compromise on your budget in order that you can purchase the metal detector which will meet the majority of your needs rather than just going for the cheapest.

When looking to purchase a second hand or used metal detector it is better if you go to a reputable dealer rather than purchasing one through an advertisement in a local newspaper. A reputable dealer will offer you a money back guarantee or allow you to exchange your old metal detector (as they will test the detectors prior to selling them) if you don't like it or find it difficult to use.

The price of a used metal detector can vary and all purpose metal detectors can range from $275 to $700, while underwater ones will usually have a price range of about $500. There are many accessories which can be purchased for your metal detector and these will start at around $200.

The only disadvantage of purchasing a second hand or used metal detector is that there will be no manufacturer's warranty with the item and as long as you buy from a reputable dealer then you know you will have some form of safety net instead (such as a money back guarantee or exchange program).

Article Source: http://EzineArticles.com

Discover How to Find a Metal Detector Without Going Broke

If you're looking a metal detector and not looking to spend a lot of money finding one that is inexpensive and effective can be a tricky proposition. You do not want to buy one that does not work very well because that will be a complete waste of money but at the same time you do not want to break the bank buying a metal detector.

Here are some things you need to consider when looking for an inexpensive metal detector.

-Do Your Research

When looking to find an inexpensive metal detector do as much research as possible so that you do not end up wasting your money. The last thing you want to do is to get an inexpensive metal detector that will find absolutely no gold, silver or anything underground that you are looking for.

Go online and type in terms such as metal detector forums, metal detector facts, and best places to buy metal detectors. Located in some of these forms you find honest opinions about metal detectors because they typically do not have any monetary interest.

-Get the Best Deal

Always take time to look around for the best deal you can find never settle for the first thing that pops up. A good way to compare pricing is to find manufacturer number and name of it detector and type it into a search engine and you will get a whole host of websites that have pricing.

If you are not familiar with pricing of metal detectors you really never know what is inexpensive and what is not inexpensive. It is best to look at comparative shopping so you will know what the price is.

-Buy from Quality Companies

If you are looking for an inexpensive metal detector buy from a company that is very reputable. The last thing you want to happen is to buy an inexpensive metal detector that is defective and not be up to get your money back or exchange it.

Any company with a good reputation will always take back a defective piece of equipment. If you are planning on buying one online there are many websites that will give user ratings for the company.

When looking for inexpensive metal detector you have to be very careful to make sure that you do not buy something that is extremely weak or fake. Nothing can be worse than metal detecting and not finding anything, follow these tips and make sure that you get the best deal possible.

J C Christian is an avid follower of metal detectors and how they work. He runs an informational site that follows Garret Metal Detectors, Fisher Metal Detectors, Tesoro Metal Detectors, and Kellyco Metal Detectors just to name a few. Go to http://www.metal-detector-guides.com to find information to help with everything metal detecting.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

3 Types of Metal Detecting to Get Involved In

Metal detecting can be a lot of fun, a wonderful hobby, and can also be a way to make money if you know what to look for. They're a lot different types of metal detecting and a lot of different places you can go to metal detect. We will look at three different ways to metal detect water and beach detecting, gold prospecting, and treasure detecting.

1. Water and beach detecting

This is one of the fastest growing types of metal detecting as until recently metal detectors were not readily available for underwater detecting. Metal detectors can search at depths of up to 200 feet which is more than sufficient for your area river, lake, or pond.

If you happen to live near an ocean you are probably a big fan of both water and beach metal detecting. On the beach you have a vast area to search and the beach is very easy to dig through and locate your treasure.

2. Prospecting for gold

Individual who prospect for gold probably make of the biggest subsection of all the metal detectors. This group can be weekend warriors or people who actually make a living at metal detecting. There has been a lot of technology introduced that makes detecting at a deeper depth possible and recovery rates better.

Prospecting for gold can be a lucrative career or a good way to make some side money this is why people get involved to stay involved.

3. Treasure detecting

This is kind of metal detecting is the catch all section of metal detecting, more people are getting involved in looking for treasure, hidden relics, and old coins. This type of metal detecting can be planning a day trip or a weekend away just to look for treasure or can be just going in your backyard and metal detecting until your heart is content.

You can basically go anywhere and start metal detecting and find some type of treasure.

Where you metal detect and the places you go is completely up to you, but one thing is for certain there is a lot of treasure out there to be had if you're on the lookout you can snag it.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

Discover Deep Treasures Below the Earths Surface-Metal Detecting Beep Beep

Metal detecting is becoming an increasingly popular hobby and with good reason because it allows you to be outside in the environment at the same time you can possibly find old relics, gold, old coins, and any other valuables that may be hidden under the grounds surface.

Listening to your signal and allowing the metal detector to tell you what is below is a skill you can be acquired by use and familiarity. There will be specific sounds for different types of treasure that lay underneath the ground. You just need to stay extremely focused on the signals that the metal detectors giving you and make a mental note of what they mean.

There are certain levels you can set a metal detector on from the lowest the highest setting. At the lowest frequency you may waste your time finding metal that is invaluable and not usable. At the same time, if you put the frequency way too high you could be missing out on a lot of valuable treasure. You need to decide after doing several searches what is the best frequency for you and what the individual beeps me.

If at all possible make sure you set of headphones to go along with the metal detector, headphones with a metal detector will give you more listening power and shield your ears from outside noises. Your ears are your most valuable asset when metal detecting if you don't want to miss anything beats good pair of headphones.

Placing the detectors as close to the ground as possible this allow you to delve deeper into the surface and hopefully you can find treasures that have been passed over by several other people.

When using a metal detector you need to pay attention to your signal and after making mental notes you may want to carry a paper log with you and write down what type of signal you heard and what you actually uncovered. You becoming familiar with your metal detector and the sounds and it makes will over time allow you to become way more efficient. Regardless, if you metal detect for the sheer joy or if you are in it for the monetary gains becoming efficient with your metal detector all depends on you becoming familiar with the sounds that it makes.

J C Christian is an avid follower of metal detectors and how they work. He runs an informational site that follows Garret Metal Detectors,Fisher Metal Detectors,Kellyco Metal Detectors ,and Tesoro Metal Detectors, and just to name a few. Go to http://www.metal-detector-guides.com to find information to help with everything metal detecting.

Article Source: http://EzineArticles.com/?expert=J_C_Christian

A Review of Popular Metal Detector Products

Metal detectors come with a control box that contains the circuitry, controls, speaker, batteries and the microprocessor; a shaft that connects the control box and the coil; a search coil that actually senses the metal; and a stabilizer that keeps the unit steady as it is moved. The performances of the detectors are based on the features of these parts.

Tesoro Metal Detectors
At less than 2½ pounds, the Tesoro Golden Max lets you control what you want to find. It is the lightest detector in the market with full size depth, sensitivity, four tone audio ID and a user adjustable Notch Filter Discriminate. The Tesoro DeLeon is a Target Identification Detector (TID), named after the famous explorer Ponce de Leon, who searched Florida looking for treasure and the Fountain of Youth. The DeLeon is designed as an easy to use, turn-on-and-go detector.

Whites Metal Detectors
The Whites E-series metal detectors include the following models. DFX™ brings together the ultimate combination of sophisticated microprocessor technology, and turn-on-and-go simplicity. It has an operational frequency of 3 kHz and 15 kHz. The XLT® Metal Detector is high-performance simplicity and versatility at its best. It has five programs to choose from along with 10 Basic Adjustments, and 29 Pro Options. The MXT has three completely separate operating modes -- gold prospecting, coin/jewelry, or relic.

Prizm series
The Prizm series include Prizm II, III, IV, and V. All have a pinpoint mode that zeroes in on target location, instruction videos that show when and where to hunt.

Fisher Metal Detectors
Dr. Gerhard Fisher, a German immigrant, obtained the first patent ever issued on aircraft radio direction finders in the late 1920s. Fisher's 1266-X comes factory shipped with 8-inch Open Center Spider Coil, instruction manual and Fisher's 5 Year Warranty. It has a duel discrimination system, which will allow you to search at a great depth. This unit does not work very well on wet saltwater beaches.

Garrett Metal Detectors
The Garrett Super Scanner hand-held detector can detect a medium-sized pistol from distance of 9"" and even a tiny 1” piece of jewelry. Simplicity of operation of this metal detector is unmatched. The Garrett SuperWand Security metal detector is one of the most popular metal detectors. It provides uniform sensitivity 360° along the scan area and pinpointing at the tip to detect weapons and other metal objects with extreme accuracy. The Garrett Magna Scanner PD 6500 Walk through metal detector has some unique features. Its ultra-enhanced multi-coil detection field pinpoints the exact location of any metal object within 33 distinct areas of the archway.

Bounty Hunter Metal Detectors
Bounty Hunter metal detectors are made by First Texas Products. The Tracker IV priced at $160 is streamlined in appearance, with only two operating controls and a mode selection switch. The Tracker IV has a built-in Automatic Ground Tracker that maintains ground balance. The Bounty Fast Tracker offers value for your money. It is a user-friendly instrument that delivers effective performance over a wide range of conditions and applications.

Minelab Metal Detectors
The Minelab Explorer II priced at approximately $1395 is a coin and jewelry detector with an operating frequency between 1.5 – 100 kHz. The signal travels deeper at a lower frequency and the signal detects objects close to the surface at a higher frequency. The Minelab Quattro MP, priced at approximately $1300, is suited for use in parks, beaches or the battlefields. Minelab’s FBS technology provides outstanding performance even on saltwater beaches.

Article Source: http://EzineArticles.com/?expert=Damian_Sofsian

Metal Detectors Ratings

Metal detectors can be employed for a variety of applications in security, humanitarian, and industrial sectors. Metal detectors ratings are helpful for newcomers to choose metal detectors that are apt for them. Generally, metal detectors are rated by cost effectiveness, features, functions and usability.

Different types of metal detectors are available. Typical metal detectors come with less features and buttons, but some are more complicated. If a customer wishes to choose metal detectors for extended use, it is better to select those with electronic features. The price of metal detectors may vary, based on features and functions. Aside from the normal rates of a detector, the customer must also spend on headphones, beach scoops, trowels, detector bag or coil cover. A good headphone extends the sound of the warning signal.

The criteria to be considered for high ranking are usability and features. Prices are yet another consideration in metal detector ratings. Metal detectors are available from under $75. Some of the top brand names such as Garrett Master Hunter CX plus and Garrett GTI 2500, range from $500 to $1000.

The most reputed dealers offer metal detectors with sophisticated features and functions. In order to stay ahead in the competitive field, companies are searching for more innovative ideas. Some companies offer metal detectors with boost amplifier and tone control.

Metal detectors ratings can be obtained in number of ways. They often include reviews, where people can obtain an impartial overview of the benefits, features and functions of the product. Newcomers are able to get dozens of metal detector ratings from online reviewers. They publish these reviews after testing the effectiveness of the model. These reviews are one of the best options to learn about the advantages and drawbacks. You will also find plenty of informative articles written by owners of particular models.

By searching online, you can find top-ranked dealers for different ranking systems. The high ranked dealers score top ranks because of their efficient customer service. These dealers also offer some kind of warranty and discount services for their products.

Internet articles, magazines and newspapers are resources where we find informative comments on metal detectors. Some of the affordable brands in the metal detecting industry are Fisher, Tesoro, Garrett and Bounty Hunter.

Article Source: http://EzineArticles.com

Metal Detector Reviews - Choose Wisely!

Metal Detector Reviews Are Beneficial

Metal detector reviews will help you find the best detector to fit your needs. Metal detector reviews will help you check out reliability of particular manufacturers, makes, and models. You should look at several different metal detector reviews prior to buying, to ensure you find a detector that will do all that you need it do, want it to do, all at a reasonable price.

What Will I Find In Such A Review?

Alerts: Detectors have an audio signal or beep, but by reading a review you will find out if the detector has a vibrating option, or a variety of tones to let you know the different types of metal you are detecting.

Depth: Metal detector reviews will let you know how far down (depth) the detector can sense metal. By reading metal detector reviews, you will find that some detectors can detect any metal object as deep as 12 inches, while some can not only detect, but also tell exact depth location.

Detection Mode: The metal detector reviews will also tell you information regarding detection modes. Usually there are detectors that have four different modes. These modes are relics (bullets, buttons, etc.); prospecting; coins; and jewelry. The metal detector reviews will let you know if you are able to use one of these modes alone, or if you can use two modes at the same time. If you use a single mode, you will have better success (or better chances) of finding what you set out to find.

Ground balance: Did you know the ground contains metal that occurs naturally in its soil? Detectors can tell you how sophisticated the detector is to find and cancel out those natural types of metals. The better makes and models of detectors will be able to tell you the exact types of metals you are looking for as you find them.

Battery life: Detectors will usually run on AA batteries, which will usually last approximately 20-30 hours.

Sensitivity: Metal detector reviews will be able to measure which makes and models have the best adjustable sensitivity ratings. This is an important factor when detecting, so you can distinguish between ground metals and your hidden treasures.

Display: Another topic metal detector reviews will cover is display. The display on detectors will vary from simple measures to complicated measures. Take a look at the models you are looking at to see what they have to offer in display.

Where Can I Find Good Reviews?

There are online sites offering reviews on metal detectors, makes, and models. Look at more than one site and review before making your final purchasing decision. Reviews are mostly opinions, so get a wide range to help you make your choice. You will be able to make an educated decision on your own, and have confidence it was the right one.

About the Author: www.detect-metal.info

Blog Archive